This product fits the following vehicles:
The series 2 EMS has some new features over the Series 1 box. It’s a all new platform that is no longer tied to the GEMs hardware. The new unit has 12 peak and hold injectors so a resistor box is no longer needed. It runs in direct fire so wasted spark is no longer used and a smoother, factory quality idle can be had. It uses either a serial port or usb so hunting around for older laptops will be a thing of the past. The internal logging has an increased capacity. With the series two you can password protect your maps so if your tuning and don’t want your work looked by others you have that option. It will work with the existing gauges so your AEM wideband or serial gauge will be a direct transition.
Key Features:
Plug n Play
Full Fuel and Timing Control, Full Standalone, Fully Adjustable
Factory Sensors OK
Factory Sensors can be retained, however if they need to be changed, (like upgrading to a bigger map sensor), AEM has a full line of sensors available and we stock them!
Basemap Included
Password Protection
Direct Fire Ignition (no resistor box required)
16 General Outputs
8 General Inputs
Use these inputs to log various additional sensor readings (Wideband, Air Temp, Fluid Pressure, etc). These inputs can also be used to trigger fail-safes for boost, meth/water/alcohol injection, and much more
4 EGT Inputs (for fuel control)
Internal Logging Memory
Log data straight to the computer and review the session with your laptop all from within the computer.
FULL IDLE CONTROL
Customizable Traction Control
Full Boost Control (with optional boost control solenoid)
3-Step Launch Control
Nitrous Control
Definable Knock Control
USB Compatible
and more..
Outputs | |
Injector Outputs | 12 Saturated |
Coil Outputs | 4 |
Selectable direct drive or 0-5V Coil Output | Yes |
Direct plug in, no jumper harness required | Yes |
General purpose LS outputs | 12 |
General purpose HS outputs | 4 |
Individual cylinder ignition trims | Yes |
Individual cylinder fuel trims | Yes |
Inputs | |
Trigger inputs (Ref/Sync) | 4 |
Analog voltage inputs | 23 |
Configurable Analog/RTD/Thermister inputs | 4 |
Switch inputs | 5 |
Lambda inputs | 2x |
Knock sensors | 2 |
User adjustable knock sensor center frequency | Yes |
Communication | |
USB comms | Yes |
RS232 comms | Yes |
Communication cables included | Yes |
Fully enabled editing/logging software included | Yes |
CAN bus equipped | Yes |
RS232 datastream output | 19 ch |
CAN datastream output | 19 ch |
Communicates with AIM Dash/Dataloggers | Yes |
Communicates with Racepak Dash/Dataloggers | Yes |
DATA Acquisition | |
Internal data logging | 1 MB |
Maximum internal logging rate (per channel) | 250 Hz |
PC logging | Yes |
Data analysis using AEMLog | Yes |
Functions and Features | |
All channels/maps/tuning options unlocked | Yes |
Boost control | Yes |
Groundspeed based boost target | Yes |
Staged injection | Yes |
Ground speed limiting | Yes |
Rate of Acceleration Control | Yes |
Overrun boost enhancement (anti-lag) | Yes |
Gear change ignition cut (shift-without-lift) | Yes |
Password protected calibrations | Yes |
Fuel & Ignition rev limiters | Yes |
"In cockpit" global fuel trim capability | Yes |
Gear dependent shift light | Yes |
Evap/Purge function | Yes |
DC Motor control | 2 Ch |
Software definable "virtual" switch inputs | 2 |
EGT Based fuel trims | Yes |
Maximum boost limit | None |
Physical Dimensions | |
Length | 192 mm |
With | 150 mm |
Height | 37 mm |
Finish | Black Anodized |